Forum: Cooling System
02-24-2023, 08:17 PM
|
Replies: 29
Views: 4,309
Great news you have it running nicely again.
...
Great news you have it running nicely again.
Food for thought - why was the carburetor gunked* up?
Perhaps there are issues upstream that, until resolved, will continue to gunk things up?
...
|
Forum: Troubleshooting
08-07-2022, 07:11 AM
|
Replies: 13
Views: 2,336
|
Forum: Troubleshooting
07-18-2022, 06:47 AM
|
Replies: 13
Views: 2,003
Once while warming up at dock I noticed steam...
Once while warming up at dock I noticed steam coming from exhaust and no water flow. Shut down and started to troubleshoot.
Went for easy to test first - is water coming in from thruhull? Nope....
|
Forum: Drive Train / Propellers
06-08-2022, 09:07 PM
|
Replies: 9
Views: 1,663
|
Forum: Exhaust System
04-14-2022, 03:06 PM
|
Replies: 14
Views: 2,247
|
Forum: Fuel System
08-21-2021, 07:21 AM
|
Replies: 4
Views: 1,454
|
Forum: Fuel System
07-18-2021, 05:01 PM
|
Replies: 26
Views: 4,822
|
Forum: Troubleshooting
07-09-2021, 07:30 AM
|
Replies: 52
Views: 10,830
One thing that has yet to be considered here is...
One thing that has yet to be considered here is the exhaust - it it was partially blocked it might permit the engine to run ok when not under load. This has been mentioned on other threads on this...
|
Forum: Troubleshooting
07-03-2021, 05:32 PM
|
Replies: 52
Views: 10,830
a fuel pressure gauge would be an excellent...
a fuel pressure gauge would be an excellent diagnostic tool for this issue.
If you watch it will running in gear and the fuel pressure remains solid, not a fuel delivery problem. If the pressure...
|
Forum: Fuel System
06-26-2021, 06:52 AM
|
Replies: 7
Views: 2,093
If you go this route make sure you use a metal...
If you go this route make sure you use a metal check valve - plastic can melt/burn...
If I had this issue I would plug the fuel line while working on carb. I feel the fewer joints there are in the...
|
Forum: Troubleshooting
06-23-2021, 03:11 PM
|
Replies: 9
Views: 1,860
|
Forum: Fuel System
05-27-2021, 04:42 PM
|
Replies: 26
Views: 4,822
Hi,
I would replace all the fuel lines while...
Hi,
I would replace all the fuel lines while I was at it. Removing the old lines from barbed fittings often tears up the inside of the line leaving little chunks of rubber that can gum up the...
|
Forum: Troubleshooting
05-25-2021, 05:21 PM
|
Replies: 12
Views: 2,398
Hey Jo,
As John suggested a while back, I...
Hey Jo,
As John suggested a while back, I would pop the distributor open and check that the centrifugal advance is working properly. Good chance it is seized after sitting unused for 1-1/2 years....
|
Forum: Ignition System
05-14-2021, 07:41 AM
|
Replies: 20
Views: 4,298
Lubr,
If you were getting spark “to the...
Lubr,
If you were getting spark “to the distributor” then the EI module was working at that point.
You had an issue getting the spark through the rotor to the plugs. I suspect that removing and...
|
Forum: General Interest
05-03-2021, 11:08 AM
|
Replies: 8
Views: 2,241
Welcome Lokeypod,
That is a frost plug that...
Welcome Lokeypod,
That is a frost plug that has popped out - see this thread for info - https://www.moyermarineforum.com/forums/showthread.php?t=11531&highlight=frost+plug+head
And of course...
|
Forum: Troubleshooting
05-01-2021, 06:36 AM
|
Replies: 21
Views: 3,049
Questions
1) what type of pump is it? Does...
Questions
1) what type of pump is it? Does it have the grease fitting on it? Based on the photo I think it may be a MMI pump
2) water jacket pressure test - did this test include the exhaust...
|
Forum: Troubleshooting
03-31-2021, 09:44 PM
|
Replies: 25
Views: 4,991
|
Forum: General Interest
03-26-2021, 08:34 PM
|
Replies: 9
Views: 1,910
|
Forum: Troubleshooting
03-17-2021, 12:13 AM
|
Replies: 41
Views: 6,847
|
Forum: Ignition System
12-15-2020, 06:07 AM
|
Replies: 20
Views: 3,893
|
Forum: Cooling System
11-12-2020, 06:36 AM
|
Replies: 21
Views: 3,973
|
Forum: Troubleshooting
10-25-2020, 10:13 AM
|
Replies: 14
Views: 3,361
See this post
...
See this post
https://www.moyermarineforum.com/forums/showpost.php?p=4829&postcount=5
"I would definitely NOT recommend Teflon tape or pipe dope for the hot section. I replaced the hot section...
|
Forum: Exhaust System
10-24-2020, 10:34 AM
|
Replies: 13
Views: 5,780
|
Forum: Cooling System
10-10-2020, 09:24 PM
|
Replies: 14
Views: 3,772
Mark,
There are two rubber seals in the pump...
Mark,
There are two rubber seals in the pump housing that are supposed to seal
1) the coolant side of the pump, and
2) the accessory drive side of the pump
You may want to pull the pump...
|
Forum: Troubleshooting
10-04-2020, 06:49 AM
|
Replies: 13
Views: 2,363
Chris,
I think I would pressure test the...
Chris,
I think I would pressure test the cooling system before investing a lot of time cleaning that goop out.
You can do the block and the manifold separately. If the block does not hold...
|