Forum: Troubleshooting
05-07-2023, 09:52 AM
|
Replies: 6
Views: 1,234
If it still doesn't seem right do another...
If it still doesn't seem right do another compression check on 3 and 4 just to ensure you have decent compression and no head gasket failure between cylinders. I think it a fire issue...
|
Forum: Troubleshooting
05-06-2023, 12:07 PM
|
Replies: 6
Views: 1,234
|
Forum: Troubleshooting
05-06-2023, 09:15 AM
|
Replies: 6
Views: 1,234
|
Forum: General Maintenance
10-10-2022, 12:03 AM
|
Replies: 5
Views: 1,951
If you need it, somewhere around here I have a...
If you need it, somewhere around here I have a beautiful Moyer split coupler for a 3/4" shaft that is sadly not compatible with my vee-drive transmission.
I bought it secondhand but unused from...
|
Forum: General Maintenance
10-06-2022, 05:08 PM
|
Replies: 5
Views: 1,951
The shaft coupler is thru-drilled, no threads. ...
The shaft coupler is thru-drilled, no threads. The engine output coupler (where it attaches) has the threads. If the two mating couplers are "rust-welded" together, I fashioned a splitter out of a...
|
Forum: Troubleshooting
11-20-2021, 09:49 AM
|
Replies: 6
Views: 1,390
|
Forum: Troubleshooting
11-19-2021, 05:10 PM
|
Replies: 6
Views: 1,390
|
Forum: Exhaust System
08-30-2021, 10:57 PM
|
Replies: 2
Views: 1,703
Once the water's injected, the exhaust temp...
Once the water's injected, the exhaust temp should be reduced, so any length of rubber hose should be fine, as long as you can physically manipulate it into place. If the hose is really short, you...
|
Forum: Overhaul
07-25-2021, 06:47 PM
|
Replies: 5
Views: 2,083
|
Forum: Overhaul
07-21-2021, 12:02 AM
|
Replies: 5
Views: 2,083
|
Forum: Overhaul
07-19-2021, 06:54 PM
|
Replies: 5
Views: 2,083
|
Forum: Overhaul
07-13-2021, 10:33 AM
|
Replies: 18
Views: 3,022
It may help to understand how an anti-siphon...
It may help to understand how an anti-siphon functions. It allows air to enter the cooling system in the event of negative pressure, a suction, thereby interrupting the suction. As you'll remember...
|
Forum: Overhaul
07-12-2021, 11:43 AM
|
Replies: 18
Views: 3,022
|
Forum: Overhaul
07-12-2021, 11:23 AM
|
Replies: 18
Views: 3,022
|
Forum: Overhaul
07-12-2021, 08:49 AM
|
Replies: 18
Views: 3,022
|
Forum: Overhaul
07-11-2021, 10:31 AM
|
Replies: 18
Views: 3,022
I agree with Dave. Your water injection is too...
I agree with Dave. Your water injection is too high. It should be at least 4" below the high spot on the dry stack. You're going to continue to get water in the manifold with that setup.
I would...
|
Forum: Overhaul
07-10-2021, 11:28 PM
|
Replies: 18
Views: 3,022
|
Forum: Exhaust System
06-25-2021, 03:43 PM
|
Replies: 2
Views: 1,000
I don't do anything...this is an updraft carb...
I don't do anything...this is an updraft carb engine. We are not talking high fuel pressure of fuel injected engines. Snug that compression gauge fitting tight so that you don't loose compression...
|
Forum: Cooling System
06-08-2021, 11:14 AM
|
Replies: 14
Views: 2,761
Vinegar is much easier to use and is a more...
Vinegar is much easier to use and is a more "forgiving" acid.
It also isn't bad for the environment if you let it flow out the exhaust into the surrounding water.
As Dave said, try that first,...
|
Forum: Cooling System
05-19-2021, 06:22 PM
|
Replies: 14
Views: 2,761
|
Forum: Cooling System
05-19-2021, 05:41 PM
|
Replies: 14
Views: 2,761
SOME IDEAS
A good summary test is to attach a hose to the manifold outlet barb, start the engine briefly and rev it up. Should be like a garden hose in output. Only do this momentarily since there will be hot...
|
Forum: Fuel System
04-22-2021, 04:12 PM
|
Replies: 2
Views: 1,032
|
Forum: Announcements
08-08-2020, 10:17 PM
|
Replies: 34
Views: 6,058
Saying goodbye
Some sixteen years after conceiving and managing the forum on a daily basis, I am stepping away from responsibility for it, A member of the MMI family will hopefully inform you soon as to whether...
|
Forum: Fuel System
05-15-2020, 06:36 PM
|
Replies: 13
Views: 4,188
|
Forum: Fuel System
05-12-2020, 01:10 PM
|
Replies: 13
Views: 4,188
|