Return to the home page...
Moyer Marine Atomic 4 Community - Home of the Afourians
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
FAQ
Members List
Search
Today's Posts
Mark Forums Read
Showing results 1 to 8 of 8
Search took
0.01
seconds.
Search:
Posts Made By:
Mark Millbauer
Forum:
Troubleshooting
10-05-2021, 06:10 PM
Replies:
55
Over propped?
Views:
6,782
Posted By
indigo
Rick, I see from my records that you had...
Rick,
I see from my records that you had Indigo Prop S/N 1474 on a C&C 30. Indigo props are installed on nearly 60 C&C 30s with no reports of the issues you have outlined.
With your 25 ft...
Forum:
General Interest
03-30-2020, 11:04 PM
Replies:
167
My A4 adventures
Views:
45,313
Posted By
Ando
The adventure continues: 1. I installed the...
The adventure continues:
1. I installed the manifold, exhaust and carb (I learned that it is a whole hell of a lot easier to install the exhaust to the manifold when the manifold is off the...
Forum:
Cooling System
03-02-2019, 06:19 PM
Replies:
7
Raw Water Intake Tee
Views:
3,447
Posted By
Sam
I set up a lady friends' 77 Catalina which had ...
I set up a lady friends' 77 Catalina which had gate valve on thru hole - very similar but instead of the cap added 6 in of galvanized pipe with another gate valve and barb to facilitate short piece...
Forum:
General Maintenance
09-04-2016, 10:41 PM
Replies:
17
What is my darned problem?
Views:
6,022
Posted By
romantic comedy
quick coil test: Take wire that goes from...
quick coil test:
Take wire that goes from coil to distributor off. All other wires on the terminal too. Hook a jumper wire on that terminal (negative). You will touch the other end to the engine...
Forum:
Drive Train / Propellers
05-16-2016, 09:45 PM
Replies:
22
motor shaft vibration
Views:
9,232
Posted By
hanleyclifford
That depends on whether you plan to do the work...
That depends on whether you plan to do the work yourself or have a yard do it. If it is simply a case of moving the engine into correct alignment most yards will charge 2 to 3 hours labor. But if the...
Forum:
General Interest
04-19-2016, 01:10 PM
Replies:
10
Questions about Atomic 4 for sale
Views:
3,492
Posted By
chowdan
Thanks everyone for the replies! I can't be...
Thanks everyone for the replies!
I can't be sure the engine hasn't been sunk. I have talked with the owner(3 owners ago) who installed the engine. He said he never had issues with it but the lady...
Forum:
Electrical
02-29-2016, 11:14 AM
Replies:
20
Battery charger safety and location
Views:
7,402
Posted By
JOHN COOKSON
After Reading Posts 17 &18........
If it is any comfort to BLH I have my charger (actually it's a maintainer) bolted high up on a locker bulkhead about 4 feet above the batteries and ~ 1 foot outboard from the batteries. The charger...
Forum:
Cooling System
12-06-2015, 01:32 AM
Replies:
5
Cooling system bypass kit, Product No. - CSOT_01_61
Views:
3,671
Posted By
JOHN COOKSON
Open and close the valve a few times every once...
Open and close the valve a few times every once in a while. This will keep the valve from "freezing" or corroding in the position it is left in. It is a good idea to do this with the valves on the...
Showing results 1 to 8 of 8
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Announcements
Introductions
Drawings and Schematics
Testing Protocols
Discussion Topics
General Interest
Polls
Helpful Videos
ABYC and USCG Standards
Troubleshooting
General Maintenance
Ignition System
Electrical
Fuel System
Cooling System
Reversing Gear
Exhaust System
Drive Train / Propellers
Overhaul
Safety
Aftermarket Kits and Accessories
Specialty Tools
Moyer Marine Pin-Up's
Good Guys
Links of Particular Interest
The Wish List
Owner Discussion Groups
Discussion Groups
Alberg
Bristol
C&C
Cal
Catalina
Columbia
Dyer Glamour Girl
Ericson
Grampian
Herreshoff
Irwin
Islander
Morgan
Newport
O'Day
Pearson
Ranger
Sabre
Tartan
Classified Ads
For Sale - Engines and Engine Parts
For Sale - Other Items
Wanted to Buy - Engines and Engine Parts
Wanted to Buy - Other items
Tools wanted or offered to rent
All times are GMT -4. The time now is
06:16 PM
.
Moyer Marine Inc.
-
Archive
-
Top
Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Universal® is a registered trademark of Westerbeke Corporation
Copyright © 2004-2024 Moyer Marine Inc.
All Rights Reserved