Forum: Fuel System
01-19-2022, 06:30 AM
|
Replies: 16
Views: 2,042
There is more than one person on here with a...
There is more than one person on here with a gauge like that installed. I have an electrical gauge I can read from the cockpit.
Regarding the squeeze bulbs, they come in handy, but I have had more...
|
Forum: Polls
01-16-2022, 02:07 PM
|
Replies: 107
Views: 75,275
|
Forum: Drive Train / Propellers
07-03-2021, 01:54 PM
|
Replies: 8
Views: 2,415
A 3/4” thick circular steel spacer with three...
A 3/4” thick circular steel spacer with three through holes and a little depression in the center to mate with the coupler face should be an easy diy build for a hobbiest with a lathe and a drill...
|
Forum: Troubleshooting
03-10-2021, 04:35 AM
|
Replies: 36
Views: 6,558
I would recommend to read that whole thread,...
I would recommend to read that whole thread, block got repaired
https://www.moyermarineforum.com/forums/showthread.php?t=10561&highlight=cracked+block&page=4
Another block with a crack on the...
|
Forum: Troubleshooting
03-09-2021, 12:20 PM
|
Replies: 36
Views: 6,558
Dan, I would not remove the "locating pins"...
Dan, I would not remove the "locating pins" unless absolutely necessary. They are "pressed" in and need to be wiggled to get out. Unless they come out easily with a pull or mild twist with pliers it...
|
Forum: General Interest
01-04-2021, 09:59 AM
|
Replies: 20
Views: 5,288
|
Forum: Ignition System
12-16-2020, 12:07 AM
|
Replies: 20
Views: 3,893
|
Forum: Introductions
12-15-2020, 10:31 PM
|
Replies: 7
Views: 4,590
ccbear - Be careful doing too many things at...
ccbear - Be careful doing too many things at once. Let's just get it running...I love the simplicity of my mech fuel pump..the worst that happens is if the diaphragm fails, it dumps fuel in the...
|
Forum: Announcements
08-08-2020, 10:17 PM
|
Replies: 34
Views: 6,053
Saying goodbye
Some sixteen years after conceiving and managing the forum on a daily basis, I am stepping away from responsibility for it, A member of the MMI family will hopefully inform you soon as to whether...
|
Forum: General Interest
05-19-2020, 01:38 PM
|
Replies: 22
Views: 4,676
I tend to trend towards the "rebuild engine in...
I tend to trend towards the "rebuild engine in mid-cruise" supply level, but I did decide the extra starter weighed a ton and took it home.
If you race, then you need two screwdrivers and vicegrips,...
|
Forum: Troubleshooting
07-29-2019, 07:11 PM
|
Replies: 15
Views: 4,511
|
Forum: Troubleshooting
07-08-2019, 08:33 AM
|
Replies: 13
Views: 4,154
The symptoms point to an inadequate fuel/air...
The symptoms point to an inadequate fuel/air ratio so what are the possibilities? Partially clogged main jet, intake vacuum leak, fuel contamination, fuel level low in the bowl. Do you have a PCV...
|
Forum: Cooling System
05-28-2019, 11:59 AM
|
Replies: 15
Views: 6,775
PS
Edward, the short small diameter is for the seal and a nic or two won't hurt as they can be "smoothed" and a bit of sealant will take care of the rest.
Good luck.
Dave Neptune :cool:
|
Forum: Cooling System
12-29-2018, 04:09 PM
|
Replies: 6
Views: 2,994
|
Forum: Troubleshooting
07-08-2018, 05:29 PM
|
Replies: 13
Views: 4,183
I'm not convinced you have a problem. The fuel...
I'm not convinced you have a problem. The fuel pump ticking is normal for pulse type pumps which leads me to your fuel pressure gauge behavior. It's pulsing nature may also be normal because of the...
|
Forum: Electrical
02-14-2018, 08:17 AM
|
Replies: 16
Views: 4,455
|
Forum: General Interest
01-17-2018, 09:38 PM
|
Replies: 12
Views: 3,961
The engine runs fine just has real low...
The engine runs fine just has real low compression and does not except throttle very quickly. You have to open the throttle 2/3 with full choke to get it to cold start to draw in enough fuel. Makes...
|
Forum: General Interest
01-13-2018, 02:52 PM
|
Replies: 7
Views: 2,608
|
Forum: Troubleshooting
01-07-2018, 11:48 AM
|
Replies: 14
Views: 4,151
|
Forum: Troubleshooting
10-17-2017, 03:49 PM
|
Replies: 12
Views: 3,896
Went down one rabbit hole, and then another...
After finding water in the gas, and discovering that the carb leaked, I thought I had a fuel problem. Nearly two months later, I had given the fuel system a going through (pumped the tank, changed...
|
Forum: Ignition System
10-16-2017, 05:30 PM
|
Replies: 42
Views: 78,117
|
Forum: Cooling System
09-30-2017, 10:02 AM
|
Replies: 24
Views: 6,035
|
Forum: Announcements
04-29-2017, 06:57 PM
|
Replies: 62
Views: 18,376
|
Forum: Overhaul
02-19-2017, 08:14 PM
|
Replies: 23
Views: 8,144
Bobin,
Removing the mixing elbow from the...
Bobin,
Removing the mixing elbow from the manifold is a piece of cake - a recip saw with a carbide blade will do it in about 30 sec. This will leave half of the nipple in each part - also removable...
|
Forum: Troubleshooting
12-07-2016, 08:58 AM
|
Replies: 2
Views: 2,704
Please read these two posts: ...
Please read these two posts:
http://www.moyermarine.com/forums/showpost.php?p=38343&postcount=196
http://www.moyermarine.com/forums/showpost.php?p=38350&postcount=198
|