Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Members List

ILikeRust's Profile Picture

ILikeRust ILikeRust is offline

Afourian MVP

Visitor Messages

Showing Visitor Messages 1 to 10 of 12
  1. ILikeRust
    01-19-2015 05:41 PM
    ILikeRust
    Hey, I just discovered your message here - I haven't logged into the forum for a long while. Sorry for taking so long to get back to you.

    I'd be glad to offer any assistance I can.
  2. River Raft
    10-20-2014 02:09 PM
    River Raft
    Tim, good afternoon. Hoping you are still around in the RIC area. I recently bought a boat with an Atomic 4 and am looking forward to tearing it down this winter. Hoping to use you as a resource perhaps?
  3. ILikeRust
    08-17-2013 08:07 PM
    ILikeRust
    Yes, I've done electrolysis on some very rusty, crusty old tools and machine parts. I've concluded it's overkill much of the time. If you've got something very crusty, with parts stuck together, it can work wonders. Other than that, if you've just got something that's rusty, there are other mechanical methods that work perfectly well to prepare the surface for paint or powder coating.
  4. Dave Neptune
    08-11-2013 04:41 PM
    Dave Neptune
    Bill, getting ready to de-rust a bike frame for a powder coating. The frame is totally rusted and been only around the beach and has had a lot of salt exposure. I'm thinking of putting together an electrolysis tub and wanted to know if you have ever done so in any of your restorations. I am not so worried about the finish as I am about actually sealing for a long lasting "powder" job
  5. Larry Wilson
    10-11-2011 10:35 PM
    Larry Wilson
    Bill,
    If you are considering a used engine, I'll let mine go for considerably less than $1500.
  6. keithems
    07-15-2011 11:16 AM
    keithems
    hi --

    it's looking like i'll have to use my 9.9 johnson for the rest of the summer -- if nothing else to get my boat back to her winter base

    so re. adding electric starting -- can you tell me how it's done? is there a kit? where would i get it? what else will i need to purchase? what is the approx. cost?

    any advice re. putting the o/b on my transom/ unfortunately, it's a short shaft johnson 9.9

    feel free to email me directly at keithems@gmail.com if you'd like
  7. jpian0923
    06-11-2011 08:23 PM
    jpian0923
    Thanks. Good advice.
  8. ILikeRust
    06-11-2011 06:30 PM
    ILikeRust
    Given how long it took us to figure out how to get it on there (which was a pain, given the big studs that stick out the front of the crankshaft), I don't think it was worth the effort.
  9. ILikeRust
    06-11-2011 06:29 PM
    ILikeRust
    No, I don't think it was worth the effort of using the engine stand. It's difficult to hook the engine up on the stand - it must have taken us an hour to finally get it on there - and I didn't like it, because there is a fair amount of weight just hanging way out there - seems a lot of strain to put on the casting.

    Yeah, it did make it a little easier to flip the engine over and then back when putting the crank and pistons back in. But after putting the crank in, I eventually ended up pretty much just leaving it sideways for putting in the pistons. I could have done that with it lying on the bench. And as soon as I had the oil pan on, I took it off the stand and put it in the dolly I had built.

    The Moyer Manual describes just putting it on a bench and flipping it over as needed. If I were to do it again, I don't know that I would bother putting it on the stand. I had mine on the stand for I think maybe a day or two.
  10. jpian0923
    06-11-2011 04:55 PM
    jpian0923
    Sweet! Thanks

    Was it worth using the engine stand? I found one at Walmart for $50.

    Take a look at this and tell me if you think it would work for the A4...
    http://www.walmart.com/search/search-ng.do?search_constraint=0&ic=48_0&Find.x=0&Find.y= 0&Find=Find&_ta=1&search_query=engine%20stand&_tt= engine%20stand

    Which bolt holes did you use?

About Me

  • About ILikeRust
    Boat Name
    Grizabella
    Home Port
    Queens Creek (Mathews), VA
    Location
    Henrico, VA
    Biography
    All-around great guy!
    Occupation
    Environmental attorney
    Interests
    Woodworking, blacksmithing, firearms, interesting automobiles, boatbuilding
  • Signature
    - Bill T.
    - Richmond, VA

    Relentless pursuer of lost causes

Statistics

Total Posts
Visitor Messages
Total Thanks
General Information
  • Last Activity: 06-15-2018 05:17 PM
  • Join Date: 09-27-2010

Friends

Showing Friends 1 to 6 of 6

All times are GMT -4. The time now is 08:16 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2018 Moyer Marine Inc.

All Rights Reserved